The washing machine doesn't start or doesn't fill: • the appliance isn't plugged in correctly, the electrical installation isn't. Working, there is a power failure. Manufacturer: Electrolux, Model: EWT 9120 W, Type of document: User manual, Category: Washer, Number of. User manual Washing Machine EWT 9120 W[.].
Operating Problems Numerous checks were carried out on your appli- ance before it left the factory. However, should you notice a malfunction, please refer to the sections below before contacting the after-sales service. Problems Causes The washing machine doesn’t start or doesn’t fill: • the appliance isn’t plugged in correctly, the electrical installation isn’t working, there is a power failure, • the lid of your appliance and the drum shutters aren’t closed firmly, • the programme start command hasn’t been properly selected, • the water supply has been cut off, the water inlet tap is closed, • the water inlet filters are dirty, • a red tab appears on the water inlet hose. The appliance fills but empties straight away: • the drainage U-piece is fixed too low (see installation section). The washing machine doesn’t rinse or doesn’t empty: • the drain hose is blocked or bent, • the object trap is obstructed, • the out of balance detector has been activated: washing is unevenly distributed in the drum, • the “Drain” programme or “Night Silence Plus” or “Rinse hold” option have been selected, • the height of the drainage U-piece is unsuitable. Ceramic 3d torrent. You have found water around the washing ma- chine: • too much detergent has caused foam to overflow, • the detergent is unsuitable for machine washing, • the drainage U-piece isn’t attached correctly, • the water inlet hose is leaking. Wash is unsatisfactory: • the detergent is unsuitable for machine washing, • there is too much washing in the drum, • the wash cycle is unsuitable, • there isn’t enough detergent.
The appliance vibrates, is noisy: • all packaging have not been removed from the appliance (see installation section), • the appliance isn’t level and is unbalanced, • the appliance is too close to the wall or furniture, • washing is unevenly distributed in the drum, the load is too small, • the appliance is in running in period. The wash cycle is much too long: • the water inlet filters are dirty, • the power or water supply has been cut off, • the motor overheating detector has been activated, • the water inlet temperature is lower than usual, • the foam detection security system has been activated (too much de- tergent) and the washing machine has begun draining the foam, • the out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. The washing machine stops during a wash cy- cle: • the water or electricity supply is defective, • a Rinse hold has been selected, • the drum shutters are open. The lid doesn’t open at the end of the cycle: • the temperature inside the drum is too high, • the lid unlocks 1 - 2 minutes after the end of the cycle.
Softener runs directly into the drum when filling the dispenser box: • you have gone past the MAX indicator. Electrolux 7.
Related Forms - Prewash Classes are filling FASTRegister Today!FALL2018 Center for Workforce Devel opment and Continuing Education NonCr edit Courses 508.751.7900 www.QCC.edu/WD 25 Classes are filling FAST REGISTER TODAY!SPRING201 8 CENTER FOR WORKFORCE DEVEL OPMENT AND CONTINUING EDUCATION NonCr edit Courses 508.751.7900 www.QCC.edu/WD 25 Version 3.0PELICAN: New Provider Training GuideO ffice of Child Development and Early Learning (OCDEL).
The washing machine doesn\'t start or doesn\'t fill: • the appliance isn\'t plugged in correctly, the electrical installation isn\'t. Working, there is a power failure. Manufacturer: Electrolux, Model: EWT 9120 W, Type of document: User manual, Category: Washer, Number of. User manual Washing Machine EWT 9120 W[.].
Operating Problems Numerous checks were carried out on your appli- ance before it left the factory. However, should you notice a malfunction, please refer to the sections below before contacting the after-sales service. Problems Causes The washing machine doesn’t start or doesn’t fill: • the appliance isn’t plugged in correctly, the electrical installation isn’t working, there is a power failure, • the lid of your appliance and the drum shutters aren’t closed firmly, • the programme start command hasn’t been properly selected, • the water supply has been cut off, the water inlet tap is closed, • the water inlet filters are dirty, • a red tab appears on the water inlet hose. The appliance fills but empties straight away: • the drainage U-piece is fixed too low (see installation section). The washing machine doesn’t rinse or doesn’t empty: • the drain hose is blocked or bent, • the object trap is obstructed, • the out of balance detector has been activated: washing is unevenly distributed in the drum, • the “Drain” programme or “Night Silence Plus” or “Rinse hold” option have been selected, • the height of the drainage U-piece is unsuitable. Ceramic 3d torrent. You have found water around the washing ma- chine: • too much detergent has caused foam to overflow, • the detergent is unsuitable for machine washing, • the drainage U-piece isn’t attached correctly, • the water inlet hose is leaking. Wash is unsatisfactory: • the detergent is unsuitable for machine washing, • there is too much washing in the drum, • the wash cycle is unsuitable, • there isn’t enough detergent.
The appliance vibrates, is noisy: • all packaging have not been removed from the appliance (see installation section), • the appliance isn’t level and is unbalanced, • the appliance is too close to the wall or furniture, • washing is unevenly distributed in the drum, the load is too small, • the appliance is in running in period. The wash cycle is much too long: • the water inlet filters are dirty, • the power or water supply has been cut off, • the motor overheating detector has been activated, • the water inlet temperature is lower than usual, • the foam detection security system has been activated (too much de- tergent) and the washing machine has begun draining the foam, • the out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. The washing machine stops during a wash cy- cle: • the water or electricity supply is defective, • a Rinse hold has been selected, • the drum shutters are open. The lid doesn’t open at the end of the cycle: • the temperature inside the drum is too high, • the lid unlocks 1 - 2 minutes after the end of the cycle.
Softener runs directly into the drum when filling the dispenser box: • you have gone past the MAX indicator. Electrolux 7.
Related Forms - Prewash Classes are filling FASTRegister Today!FALL2018 Center for Workforce Devel opment and Continuing Education NonCr edit Courses 508.751.7900 www.QCC.edu/WD 25 Classes are filling FAST REGISTER TODAY!SPRING201 8 CENTER FOR WORKFORCE DEVEL OPMENT AND CONTINUING EDUCATION NonCr edit Courses 508.751.7900 www.QCC.edu/WD 25 Version 3.0PELICAN: New Provider Training GuideO ffice of Child Development and Early Learning (OCDEL).
...'>Stiraljnaya Mashina Electrolux Ewt 9120 W Instrukciya(22.03.2019)The washing machine doesn\'t start or doesn\'t fill: • the appliance isn\'t plugged in correctly, the electrical installation isn\'t. Working, there is a power failure. Manufacturer: Electrolux, Model: EWT 9120 W, Type of document: User manual, Category: Washer, Number of. User manual Washing Machine EWT 9120 W[.].
Operating Problems Numerous checks were carried out on your appli- ance before it left the factory. However, should you notice a malfunction, please refer to the sections below before contacting the after-sales service. Problems Causes The washing machine doesn’t start or doesn’t fill: • the appliance isn’t plugged in correctly, the electrical installation isn’t working, there is a power failure, • the lid of your appliance and the drum shutters aren’t closed firmly, • the programme start command hasn’t been properly selected, • the water supply has been cut off, the water inlet tap is closed, • the water inlet filters are dirty, • a red tab appears on the water inlet hose. The appliance fills but empties straight away: • the drainage U-piece is fixed too low (see installation section). The washing machine doesn’t rinse or doesn’t empty: • the drain hose is blocked or bent, • the object trap is obstructed, • the out of balance detector has been activated: washing is unevenly distributed in the drum, • the “Drain” programme or “Night Silence Plus” or “Rinse hold” option have been selected, • the height of the drainage U-piece is unsuitable. Ceramic 3d torrent. You have found water around the washing ma- chine: • too much detergent has caused foam to overflow, • the detergent is unsuitable for machine washing, • the drainage U-piece isn’t attached correctly, • the water inlet hose is leaking. Wash is unsatisfactory: • the detergent is unsuitable for machine washing, • there is too much washing in the drum, • the wash cycle is unsuitable, • there isn’t enough detergent.
The appliance vibrates, is noisy: • all packaging have not been removed from the appliance (see installation section), • the appliance isn’t level and is unbalanced, • the appliance is too close to the wall or furniture, • washing is unevenly distributed in the drum, the load is too small, • the appliance is in running in period. The wash cycle is much too long: • the water inlet filters are dirty, • the power or water supply has been cut off, • the motor overheating detector has been activated, • the water inlet temperature is lower than usual, • the foam detection security system has been activated (too much de- tergent) and the washing machine has begun draining the foam, • the out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. The washing machine stops during a wash cy- cle: • the water or electricity supply is defective, • a Rinse hold has been selected, • the drum shutters are open. The lid doesn’t open at the end of the cycle: • the temperature inside the drum is too high, • the lid unlocks 1 - 2 minutes after the end of the cycle.
Softener runs directly into the drum when filling the dispenser box: • you have gone past the MAX indicator. Electrolux 7.
Related Forms - Prewash Classes are filling FASTRegister Today!FALL2018 Center for Workforce Devel opment and Continuing Education NonCr edit Courses 508.751.7900 www.QCC.edu/WD 25 Classes are filling FAST REGISTER TODAY!SPRING201 8 CENTER FOR WORKFORCE DEVEL OPMENT AND CONTINUING EDUCATION NonCr edit Courses 508.751.7900 www.QCC.edu/WD 25 Version 3.0PELICAN: New Provider Training GuideO ffice of Child Development and Early Learning (OCDEL).
...'>Stiraljnaya Mashina Electrolux Ewt 9120 W Instrukciya(22.03.2019)