20
окт
Any Chance someone has Autocad LT 2002 SP1? (K030ltss1_K044_aclt_unl.exe) Welcome to CAD Everything, an archive of CAD discussion. Results 1 to 4 of 4.
Hello ChristopherTaiwo, It looks like AutoCAD 2002 is not compatible with Windows 7. Refer the link for more information. I would suggest you to install AutoCAD in compatibility mode and then check if this fixes the issue. Follow the steps mentioned below to install in compatibility mode: a. Usk7 krautkramer manual pdf. Right click on the setup file of the AutoCAD, click Properties, click Compatibility tab, under compatibility mode, make a check mark next to “Run this program in compatibility mode for:” and select “Windows Vista (Service Pack 1 or 2) or Windows XP (Service Pact 2 or 3)” from the drop down list.
Click Apply and then click ok. Under “Privilege level” click “Run this program as an administrator”, click apply and then click ok. Install the AutoCAD successfully and restart the computer for the changes to take effect. Launch the software and check for its functionality. Also I would suggest you to view the following articles for more information about compatibility mode.
• Obtain your copy of the Longbow Converter • Using Windows Explorer, backup your entire AutoCAD 2002 CD to your hard drive, to a folder path c: Autodesk CDs acad2002 • Start the Longbow Converter tool • select the 2nd tab titled “ Old AutoCAD Installer Reviver“ • Using the ‘’ button, pick the c: Autodesk CDs acad2002folder (where you just copied your 2002 CD) • Click the “ Run Old Installer” button. • Read and understand all the prompts before pressing OK.
• Once the setup starts, stop and read the next step • In the setup program, navigate through each setup dialog as normal, except when you get to the installation folder, ** it’s vitally important to make sure you install to c: acad2002 (not Program Files (x86) AutoCAD 2002 as usually prompted by default)** • IMPORTANT NOTE: You may find that entering the path C: acad2002 may not take (a bug in the AutoCAD 2002 installer). In that case, you will need to select the installation folder C: Program Files (x86) AutoCAD 2002 in step (5) below • Do not reboot if prompted to do so • Once installed, go back to the Converter tool • Select the 3rd tab titled “ Old AutoCAD Program Reviver“ • Using the ‘’ button, pick the newly installed c: acad2002folder • click “ Fix Old Program“. • Now run your AutoCAD 2002 and completely register as normal.
Once registered, exit AutoCAD and continue to the next step • Next, unzip and save to c: Autodesk sp – do not install yet • Go back into the Converter • Select the 3rd tab again • titled “ Old AutoCAD Program Reviver“ • Using the ‘’ button, select the c: Autodesk sp folder • click “ Fix Old Program“ • Finally, install the AutoCAD 2002 sp1 by running the c: Autodesk sp acad2002sp1.exe • Now, you can happily run your AutoCAD 2002 on Windows 10, Windows 7 and Windows 8.
Any Chance someone has Autocad LT 2002 SP1? (K030ltss1_K044_aclt_unl.exe) Welcome to CAD Everything, an archive of CAD discussion. Results 1 to 4 of 4.
Hello ChristopherTaiwo, It looks like AutoCAD 2002 is not compatible with Windows 7. Refer the link for more information. I would suggest you to install AutoCAD in compatibility mode and then check if this fixes the issue. Follow the steps mentioned below to install in compatibility mode: a. Usk7 krautkramer manual pdf. Right click on the setup file of the AutoCAD, click Properties, click Compatibility tab, under compatibility mode, make a check mark next to “Run this program in compatibility mode for:” and select “Windows Vista (Service Pack 1 or 2) or Windows XP (Service Pact 2 or 3)” from the drop down list.
Click Apply and then click ok. Under “Privilege level” click “Run this program as an administrator”, click apply and then click ok. Install the AutoCAD successfully and restart the computer for the changes to take effect. Launch the software and check for its functionality. Also I would suggest you to view the following articles for more information about compatibility mode.
• Obtain your copy of the Longbow Converter • Using Windows Explorer, backup your entire AutoCAD 2002 CD to your hard drive, to a folder path c: Autodesk CDs acad2002 • Start the Longbow Converter tool • select the 2nd tab titled “ Old AutoCAD Installer Reviver“ • Using the ‘’ button, pick the c: Autodesk CDs acad2002folder (where you just copied your 2002 CD) • Click the “ Run Old Installer” button. • Read and understand all the prompts before pressing OK.
• Once the setup starts, stop and read the next step • In the setup program, navigate through each setup dialog as normal, except when you get to the installation folder, ** it’s vitally important to make sure you install to c: acad2002 (not Program Files (x86) AutoCAD 2002 as usually prompted by default)** • IMPORTANT NOTE: You may find that entering the path C: acad2002 may not take (a bug in the AutoCAD 2002 installer). In that case, you will need to select the installation folder C: Program Files (x86) AutoCAD 2002 in step (5) below • Do not reboot if prompted to do so • Once installed, go back to the Converter tool • Select the 3rd tab titled “ Old AutoCAD Program Reviver“ • Using the ‘’ button, pick the newly installed c: acad2002folder • click “ Fix Old Program“. • Now run your AutoCAD 2002 and completely register as normal.
Once registered, exit AutoCAD and continue to the next step • Next, unzip and save to c: Autodesk sp – do not install yet • Go back into the Converter • Select the 3rd tab again • titled “ Old AutoCAD Program Reviver“ • Using the ‘’ button, select the c: Autodesk sp folder • click “ Fix Old Program“ • Finally, install the AutoCAD 2002 sp1 by running the c: Autodesk sp acad2002sp1.exe • Now, you can happily run your AutoCAD 2002 on Windows 10, Windows 7 and Windows 8.
...'>Autocad Lt 2002 Service Pack 1(20.10.2018)Any Chance someone has Autocad LT 2002 SP1? (K030ltss1_K044_aclt_unl.exe) Welcome to CAD Everything, an archive of CAD discussion. Results 1 to 4 of 4.
Hello ChristopherTaiwo, It looks like AutoCAD 2002 is not compatible with Windows 7. Refer the link for more information. I would suggest you to install AutoCAD in compatibility mode and then check if this fixes the issue. Follow the steps mentioned below to install in compatibility mode: a. Usk7 krautkramer manual pdf. Right click on the setup file of the AutoCAD, click Properties, click Compatibility tab, under compatibility mode, make a check mark next to “Run this program in compatibility mode for:” and select “Windows Vista (Service Pack 1 or 2) or Windows XP (Service Pact 2 or 3)” from the drop down list.
Click Apply and then click ok. Under “Privilege level” click “Run this program as an administrator”, click apply and then click ok. Install the AutoCAD successfully and restart the computer for the changes to take effect. Launch the software and check for its functionality. Also I would suggest you to view the following articles for more information about compatibility mode.
• Obtain your copy of the Longbow Converter • Using Windows Explorer, backup your entire AutoCAD 2002 CD to your hard drive, to a folder path c: Autodesk CDs acad2002 • Start the Longbow Converter tool • select the 2nd tab titled “ Old AutoCAD Installer Reviver“ • Using the ‘’ button, pick the c: Autodesk CDs acad2002folder (where you just copied your 2002 CD) • Click the “ Run Old Installer” button. • Read and understand all the prompts before pressing OK.
• Once the setup starts, stop and read the next step • In the setup program, navigate through each setup dialog as normal, except when you get to the installation folder, ** it’s vitally important to make sure you install to c: acad2002 (not Program Files (x86) AutoCAD 2002 as usually prompted by default)** • IMPORTANT NOTE: You may find that entering the path C: acad2002 may not take (a bug in the AutoCAD 2002 installer). In that case, you will need to select the installation folder C: Program Files (x86) AutoCAD 2002 in step (5) below • Do not reboot if prompted to do so • Once installed, go back to the Converter tool • Select the 3rd tab titled “ Old AutoCAD Program Reviver“ • Using the ‘’ button, pick the newly installed c: acad2002folder • click “ Fix Old Program“. • Now run your AutoCAD 2002 and completely register as normal.
Once registered, exit AutoCAD and continue to the next step • Next, unzip and save to c: Autodesk sp – do not install yet • Go back into the Converter • Select the 3rd tab again • titled “ Old AutoCAD Program Reviver“ • Using the ‘’ button, select the c: Autodesk sp folder • click “ Fix Old Program“ • Finally, install the AutoCAD 2002 sp1 by running the c: Autodesk sp acad2002sp1.exe • Now, you can happily run your AutoCAD 2002 on Windows 10, Windows 7 and Windows 8.
...'>Autocad Lt 2002 Service Pack 1(20.10.2018)